pasobprimary.blogg.se

1. Delta rockwell table saw jointer combo value how to#
2. Delta rockwell table saw jointer combo value manual#

I will get a cast iron pulley for the motor end.Īlso, thanks for the tip on the biesemeyer fences. Sounds like I'd bee better off with a 2 hp motor, but would it better vibration wise to go for a 1725 or a 3450? I would sort of think that the 1725 would be better virbrationally, but it probebly mainly comes down the quality of the motor. The stock saw came either with a 3/4 hp 3450 rpm motor and a 2 1/2 inch pulley, or with a 1/2 hp 1725 rpm motor with a 5 inch pulley.

Delta rockwell table saw jointer combo value manual#

I had no idea that they helped to dampen virbation!įrom the manual that Dean hooked me up with it seems that the blade wants to spin at 3850 rpm which is 8100 sfm. I love them for their convenence and durablity.

Thanks for the hook up, that manual is great! If not, I'll probebly just leave the thing in place and not worry about it. If you've got one and don't need it, I'd love to have it. Not getting it though? Thanks for the offer of a new nut. I'm going to leave it together though given that these nuts are so valuable. Just sort of want to clean the whole think up and make it look like new and there is some rust that is going to be much easier to get to with the thing appart than together. I got that one off no prob, so I can adjust my backlash, but this other one probebly doesn't really need to come off. It is locked in place by one of these fancy jam nuts. I guess I don't really need to remove the one that is stuck, but in general, the backlash for the vertaical blade adjustment seems to be set by rotating an odd sort of off-set bored bushing that will holds the worm gear shaft. I'd make the nuts you need - MSC stocks the 5/8 - 20 hand tap. I bought mine on their "closeout specials" website You'll want to check this every few days as the items available change rapidly. The rip fence is always the weakest part of any saw, and Biesemeyer makes one of the best replacements. The result is the radius of the largest sheave you can put on the arbor. Raise the saw arbor to the highest setting and measure the distance from the top of the saw arbor to the bottom of the table, then add half the diameter of the arbor. The TEFC motor is internally cooled and made for this application.Ī link belt will help reduce vibration (Fenner PowerTwist ) Solid cast-iron sheaves on the motor & the saw arbor also help (Browning )īelt drive saws have a limited amount of clearance between the saw arbor & the underside of the table - most use a sheave that's about 3" diameter. The reason is that the ODP motor self-destructs when used in table-saw service - the sawdust gets sucked right into the windings. Be sure to get a TEFC-motor instead of an open drip-proof (ODP). Two to three HP is a good size for the motor on that saw.

Delta rockwell table saw jointer combo value how to#

One question is what size pulley to get for the new motor? Not really sure what sort of cutting speed would be ideal.Īny thoughts on how to find out what model i've got, or on pulley size/cutting speed would be much appreciated. It is a belt drive, and the craftsman of the same era at the yard sale had an old 1/3hp 3450 rpm motor on it, so I was thinking I'd go for the same. though they seem to be running pretty well, and then reassemble, and get a motor for it. My plan is to clean up the rust, possibly replace the main ball bearings. It's castings have some markings, but as far as I can tell there is no model number or anything. It has a cast iron table and wings and looks like it might be from the 60's. It is a small model (which is good for me) Looks like it might only take an 8" blade. I was out yard saleing last weekend and was able to pick up an old Rockwell/Delta table saw for $20! It's been sitting for a while and it's not working, but it looks entirely restorable and should be a hell of a lot better than the old ryobi hand-me-down tablesaw i've got right now.